Search Reported Parts

Search Companies

Search Member Inventories

Standards

 



Standards

AIR6273 - Terms and Definitions - Fraudulent/Counterfeit Electronic Parts
Published By: SAE
Date Published: WIP


Scope:
This document is to be used and cited as a standard reference by other SAE G-19 Committee documents that address the mitigation of Fraudulent/Counterfeit Electronic Parts.

Learn More: http://standards.sae.org/wip/air6273/

 


ARP6178 - Fraudulent/Counterfeit Electronic Parts; Tool for Risk Assessment of Distributors.
Published By: SAE
Date Published: 2011-12-19


Scope:
This SAE Aerospace Recommended Practice is applicable for all organizations that procure electronic components from sources other than the original component manufacturer. It is especially applicable for assessing distributors that sell electronic components without contractual authorization from the original component manufacturer.

Purchase Now: http://standards.sae.org/arp6178/

 

AS5553B - Fraudulent/Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition
Revision Number: B
Published By: SAE
Date Published: 2016-09-12


Scope
This standard is for use by organizations that procure and/or integrate EEE parts and/or assemblies containing such items. The requirements of this standard are generic and intended to be applied/flowed down, as applicable, through the supply chain to all organizations that procure EEE parts and/or assemblies, regardless of type, size, and product provided. The mitigation of counterfeit EEE parts in this standard is risk-based and these mitigation steps will vary depending on the application, desired performance, and reliability of the equipment/hardware.

Purchase Now: http://standards.sae.org/as5553b/

 

ARP6328 - Guideline for Development of Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition Systems
Published By: SAE
Date Published: 2016-09-12


Scope
This document contains guidance for implementing a counterfeit mitigation program in accordance with AS5553. The information contained in this document is intended to supplement the requirements of a higher level quality standard (e.g., AS9100) and other quality management system documents. This is not intended to stand alone, supersede, or cancel requirements found in other quality management system documents, requirements imposed by contracting authorities, or applicable laws and regulations unless an authorized exemption/variance has been obtained.

Purchase Now: http://standards.sae.org/arp6328/

 

AS6081 - Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition - Distributors.
Published By: SAE
Date Published: 2012-11-07


Scope:
This SAE Aerospace Standard standardizes practices to: a. identify reliable sources to procure parts, b. assess and mitigate risk of distributing fraudulent/counterfeit parts, c. control suspect or confirmed fraudulent/counterfeit parts, d. and report suspect and confirmed fraudulent/counterfeit parts to other potential users and Authority Having Jurisdiction.

Purchase Now: http://www.sae.org/technical/standards/AS6081

 


AS6171 - Test Methods Standard; General Requirements, Suspect/Counterfeit, Electrical, Electronic, and Electromechanical Parts
Published By: SAE
Date Published: 2016-10-30


Scope:
This SAE Aerospace Standard (AS) standardizes inspection and test procedures, workmanship criteria, and minimum training and certification requirements to detect Suspect/Counterfeit (SC) Electrical, Electronic, and Electromechanical (EEE) parts. The requirements of this document apply once a decision is made to use parts with unknown chain of custody that do not have pedigree back to the original component manufacturer, or have been acquired from a broker or independent distributor, or when there are other known risk elements that result in the User/Requester to have concerns about potential SC EEE parts. The tests specified by this standard may also detect occurrences of malicious tampering, although the current version of this standard is not designed specifically for this purpose.

Purchase Now: http://standards.sae.org/as6171/

 

AS6174A - Counterfeit Materiel; Assuring Acquisition of Authentic and Conforming Materiel.
Revision Number: A
Published By: SAE
Date Published: 2014-07-29


Scope
This SAE Standard standardizes practices to: a. maximize availability of authentic materiel (made from the proper materials using the proper processes with required testing,) b. procure materiel from reliable sources, c. assure authenticity and conformance of procured materiel, d. control materiel identified as counterfeit, and e. report counterfeit materiel to other potential users and government investigative authorities.

Purchase Now: http://standards.sae.org/as6174/

 


AS6301 - Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition - Distributors Verification Criteria
Published By: SAE
Date Published: WIP


Scope:
The criteria in this document is to be used by accredited Certification Bodies (CBs) to determine compliance and grant certification to AS6081, Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition - Distributors.

Learn More: http://standards.sae.org/wip/as6301/

 


AS6462 - AS5553, Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition Verification Criteria.
Revision Number: A
Published By: SAE
Date Published: 2014-08-26


Scope:
This set of criteria is to be utilized by accredited Certification Bodies (CBs) to establish compliance, and grant certification to AS5553, Aerospace Standard; Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition.

Purchase Now: http://standards.sae.org/as6462/

 


AS6496 - Fraudulent/Counterfeit Electronic Parts: Avoidance, Detection, Mitigation, and Disposition – Authorized/Franchised Distribution
Published By: SAE
Date Published: 2014-08-20


Scope:
This SAE Aerospace Standard (AS) identifies the requirements for mitigating counterfeit products in the Authorized Distribution supply chain by the Authorized Distributor. If not performing Authorized Distribution, such as an Authorized Reseller, Broker, or Independent Distributor, refer to another applicable SAE standard.

Purchase Now: http://standards.sae.org/as6496/

 


AS9003A, Inspection and Test Quality Systems, Requirements for Aviation, Space, and Defense Organizations
Revision Number: A
Published By: SAE
Date Published: 2012-07-31


Scope:
This standard includes selected quality system requirements from ISO 9001:2008[1] and AS9100:2009 applicable to noncomplex products and associated manufacturing processes. ISO 9001 text incorporated into this standard appears in standard font; while aviation, space, and defense industry additional requirements, definitions, and notes are presented in bold, italic text. The requirements of this standard are intended to be applied in whole, without any exclusions. Compliance with all corresponding AS9100 requirements is considered to meet/exceed compliance with the requirements of this standard. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence. The process approach described in ISO 9001 and AS9100 applies to this standard.

Purchase Now: http://standards.sae.org/as9003a/

 


AS9100C, Quality Management Systems - Requirements for Aviation, Space and Defense Organizations
Revision Number: C
Published By: SAE
Date Published: 2009-01-15


Scope:
This International Standard specifies requirements for a quality management system where an organization a) needs to demonstrate its ability to consistently provide product that meets customer and applicable statutory and regulatory requirements, and b) aims to enhance customer satisfaction through the effective application of the system, including processes for continual improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory requirements. NOTE 1 In this International Standard, the term 'product' only applies to a) product intended for, or required by, a customer, b) any intended output resulting from the product realization processes. NOTE 2 Statutory and regulatory requirements can be expressed as legal requirements.

Purchase Now: http://standards.sae.org/as9100c/

 


AS9120A, Quality Management Systems - Requirements for Aviation, Space and Defense Distributors
Revision Number: A
Published By: SAE
Date Published: 2009-06-29


Scope:
This standard includes ISO 9001:2008 quality management system requirements and specifies additional aviation, space and defense industry requirements, definitions and notes as shown in bold, italic text. It is emphasized that the requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.

Purchase Now: http://standards.sae.org/as9120a/

 


TB0003, Counterfeit Parts & Materials Risk Mitigation
Published By: SAE
Date Published: 2009-02-01


Scope:
This Technical Bulletin covers the following areas of concern. Prevention: Actions recommended for procuring parts and materials with a full warranty; Actions recommended for minimizing risks and protecting your Program from counterfeiting; Actions recommended when buying from a non-authorized supplier. Detection: Actions recommended when procuring parts from an unauthorized supplier or otherwise suspect that a part or material at risk of being counterfeit has been procured. Risk Mitigation: Actions recommended when no reasonable alternatives exist (e.g., a redesign is required, an unacceptable schedule delay will result, the program or customer cannot bear the additional cost) and the decision has been made to procure from a non-authorized supplier.

Purchase Now: http://standards.sae.org/tb0003/

 


CCAP-101- Counterfeit Components Avoidance Program, Certification For
Revision Number: E
Published By: Component Technology Institute, Inc. (CTI)
Date Published: 2013-11-13


Scope:
This document describes a Certification Program for the detection and avoidance of counterfeit components supplied by Independent Distributors (ID). Implementation of this Program is mandatory for IDs to become Certified to CCAP-101 for Counterfeit Components Avoidance. The ID Procedures are designed for components purchased from the open market, not from OCM or Franchised Distributor (FD) and shall address both commercial electronic components and military electronic components and applies only to new components, which have never been installed on circuit boards or in equipment. The Certification Program provides for a choice of Level A (which includes electrical testing) or Level B (which excludes electrical testing except for specified passives). The customer must specify the level A or B to be supplied.

Purchase Now: http://www.cti-us.com/CCAP.htm

 


Defense Standard 05-135 (DEF STAN 05-135) Avoidance of Counterfeit Materiel
Published By: UK Ministry of Defense
Date Published: 2014-07-10


Scope:
This Defence Standard defines the arrangements that a supplier is required to establish to demonstrate that they are actively planning and managing the risk of counterfeit materiel in their supply chain to prevent delivery of such materiel to the MOD.

Access (requires registration) Now: http://www.dstan.mod.uk

 


EIA/ECA-CB21 Counterfeit Passive Components
Published By: EIA Electronic Industries Alliance Technology Strategy & Standards
Date Published: 2005-11


Scope:
A Statement issued by members of EIA/ECA Steering Committee S-1

Download Now: http://www.ec-central.org/engineering/bulletin/CB21.pdf

 


IDEA-STD-1010-B - Acceptability of Electronic Components Distributed in the Open Market
Published By: Independent Distributors of Electronics Association (IDEA)
Date Published: April 2011


Scope:
The standard sets forth practices and requirements for visual examination and acceptability criteria of electronic components purchased and sold in the Open Market.

Learn More: http://www.idofea.org/products/52-idea-std-1010-b

 


IEC TS 62668-2:2014 - Process management for avionics - Counterfeit prevention - Part 2: Managing electronic components from non-franchised sources
Revision Number: 1.0
Published By: International Electrotechnical Commission (IEC)
Date Published: 2014-07-09


Scope:
IEC TS 62668-2:2014(en) defines requirements for avoiding the use of counterfeit, recycled and fraudulent components when these components are purchased outside of franchised distributor networks for use in the aerospace, defence and high performance (ADHP) industries. This practice is used, as derogation, only when there are no reasonable or practical alternatives. Although developed for the ADHP industry, this document may be used by other high-performance and high-reliability industries, at their discretion.

Learn More: https://webstore.iec.ch/publication/7339

 


IEC/TS 62668-1 ed2.0 - Process management for avionics - Counterfeit prevention - Part 1: Avoiding the use of counterfeit, fraudulent and recycled electronic components
Revision Number: 2.0
Published By: International Electrotechnical Commission (IEC)
Date Published: 2014-07-10


Scope:
IEC TS 62668-1:2014(en) defines requirements for avoiding the use of counterfeit, recycled and fraudulent components used in the aerospace, defence and high performance (ADHP) industries. It also defines requirements for ADHP industries to maintain their intellectual property for all of their products and services. The risks associated with purchasing components outside of franchised distributor networks are considered in IEC TS 62668-2. Although developed for the avionics industry, this specification may be applied by other high performance and high reliability industries at their discretion. This new edition includes the following significant technical changes with respect to the previous edition:
  • update of "fraudulent component" definition, addition of "recycled component" and "suspect component" definitions, and update of the concerned clauses accordingly;
  • addition of counterfeit awareness training as a requirement;
  • revision to update all references and web links in the annexes.
Purchase Now: http://webstore.iec.ch/webstore/webstore.nsf/ArtNum_PK/49868!openDocument

 


JESD243 - Counterfeit Electronic Parts: Non-Proliferation for Manufacturers
Published By: JEDEC
Date Published: March 2016


Scope:
This standard identifies the best commercial practices for mitigating and/or avoiding counterfeit products by all manufacturers of electronic parts including, but not limited to original component manufacturers (OCMs), authorized aftermarket manufacturers, and other companies that manufacture electronic parts under their own logo, name, or trademark. The types of product this standard applies to is limited to monolithic microcircuits, hybrid microcircuits and discrete semiconductor products.

Download Now (Requires registration): https://www.jedec.org/standards-documents/docs/jesd243

 


JESD31D.01 General Requirements for Distributors of Commercial and Military Semiconductor Devices
Revision Number: 01
Published By: JEDEC Solid State Technology Association
Date Published: 2012-09


Scope:
This publication identifies the general requirements for Distributors that supply Commercial and Military products. This standard applies to all discrete semiconductors, integrated circuits and Hybrids, whether packaged or in wafer/die form, manufactured by all Manufacturers. The requirements defined within this publication are only applicable to products for which ownership remains with the Distributor or Manufacturer.

Download Now (Requires registration): http://www.jedec.org/user/register?destination=node/14646

 


Open Trusted Technology Provider™ Standard (O-TTPS), Version 1.0 Mitigating Maliciously Tainted and Counterfeit Products
Revision Number: 1.0
Published By: The Open Group
Date Published: 2013-04


Scope:
The O-TTPS is an open standard containing a set of organizational guidelines, requirements, and recommendations for integrators, providers, and component suppliers to enhance the security of the global supply chain and the integrity of Commercial Off The Shelf (COTS) Information and Communication Technology (ICT). This standard if properly adhered to will help assure against maliciously tainted and counterfeit products throughout the COTS ICT product life cycle encompassing the following phases: design, sourcing, build, fulfillment, distribution, sustainment, and disposal.

Download Now: https://www2.opengroup.org/ogsys/catalog/c139

 


SEMI T20-0710 - Specification for Authentication of Semiconductors and Related Products
Revision Number: 0710
Published By: SEMI International Standards
Date Published: 2010-09-04


Scope:
The semiconductor industry has lacked standardized methods to validate the integrity of goods from non-certified distributors or suppliers. The purpose of this specification is to describe the system architecture aspect of an authentication process to establish the trusted identity of products or objects. This specification is the basic element of a suite of standards. This suite of standards is being developed in response to a request from the Anti-Counterfeiting Task Force aimed at enabling automated, reliable, and secure product authentication for the semiconductor industry, thereby reducing the presence of illegal counterfeit items in the marketplace.

Purchase Now: http://ams.semi.org/ebusiness/standards/SEMIStandardDetail.aspx?ProductID=211&DownloadID=1685

 


TCS001
Published By: Aerospace Industries Association (AIA/NAS)
Date Published: 2014-11-21


Scope:
The standard practices established in this document provide guidance on the processes and practices necessary or recommended for a company to control technology, including technical data, subject to the Export Administration Regulations (EAR).

Download Now: https://global.ihs.com/doc_detail.cfm?&rid=AIA&item_s_key=00635554&item_key_date=880502&input_doc_number=&input_doc_title=tcs001&org_code=AIA%2FNAS#abstract

 


FAA AC 00-56A - Voluntary Industry Distributor Accreditation Program
Revision Number: A
Published By: Federal Aviation Administration
Date Published: 2002-06-12


Scope:
Describes a system for the voluntary accreditation of civil aircraft parts distributors on the basis of voluntary industry oversight and provides information that may be used for developing accreditation programs. The FAA believes such programs will assist in alleviating lack of documentation and will improve traceability.

Download Now: http://www.faa.gov/regulations_policies/advisory_circulars/index.cfm/go/document.information/documentID/22293